ASTM D4417 PDF

February 18, 2021 0 By admin

For hot-dip galvanizing applications, it is possible to measure and verify the steel surface profile according to ASTM D, Standard Test. ASTM D – 11 Standard Test Methods for Field Measurement of Surface Profile of Blast – Download as PDF File .pdf), Text File .txt) or read. ASME B, Surface Texture (Surface Roughness, Waviness and Lay); ASTM D, Standard Test Methods for Measurement of Surface Profile of Blast.

Author: Akinomuro Shaktigor
Country: Cambodia
Language: English (Spanish)
Genre: Travel
Published (Last): 3 June 2006
Pages: 467
PDF File Size: 15.91 Mb
ePub File Size: 15.57 Mb
ISBN: 915-7-80545-468-3
Downloads: 77144
Price: Free* [*Free Regsitration Required]
Uploader: Dik

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Leave this field empty. Last previous edition approved in as D — 93 These changes reflect industry research on current tooling which revealed averaged measurements are consistently less than the values obtained using replica tape.

Differences in Surface Profile Measurements: ASTM D4417- Method B vs. Method C

Visual Comparator – This test method, as well as the comparator discs available on the market, have stayed the same, and therefore there were no updates for this test method.

Historical Version s – view previous versions of standard Work Item s – proposed revisions of this standard Translated Version s: The three test methods described within D for measuring surface profile include visual comparators, surface profile depth micrometers, and replica tape.

This is done because of evidence that coatings performance in any one small area is primarily influenced by the highest surface features in that area and not by the average roughness. At each location make ten readings and determine the mean.

The surface profile must be sstm with the coating system. Hold the gage by its base and press? Recent changes to ASTM D provide updated test methods to reflect the latest advances in technology and newly d417 industry research. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

  ALBENIZ ZAMBRA GRANADINA PDF

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. This is done because of evidence that coatings performance in any one small area is primarily in? Your email address will not be published.

What is Surface Profile and Why is it Necessary? Leave a Reply Cancel reply Your email address will not be published. The base of the instrument rests on the tops of the peaks of the surface pro? Larger repair areas or prepared hot-dip galvanized surfaces for painting can be measured with two readings taken from a minimum of three, 6×6 inch 15×15 cm areas. Replica Tape – Although the technology has remained mostly dd4417 for replica tape since its introduction, industry research has addressed the sufficient number of readings required to achieve an accurate measurement.

Instead, astk of the highest reading when using a depth micrometer most closely matches the same measurements produced using replica tape.

Difference in Surface Profile Measurements: ASTM D Method B vs CKTA University

Each area is marked giving the nominal pro? The instruments described are readily portable and sufficiently sturdy for use in the?

Do not drag the instrument across the surface between readings, or the spring-loaded tip may become rounded leading to false readings. Current edition approved May 10, The comparator areas are used with or without magni? There are additional techniques suitable for laboratory use not covered by these test methods. According to ASTM D, a minimum of 2 readings is obtained per area; the average of the two readings is reported.

  GEEZ AMHARIC DICTIONARY PDF

A burnishing tool is used to impress the foam face of the tape into the surface to create a reverse atsm of the pro?

For this reason, surface profile should be measured prior to coating application to ensure that it meets that specified. At each location make three readings and determine the mean.

Historical Version s – view previous versions of standard. Anyone making use of this information assumes all liability arising from such use. Standards for Measurement of Surface Profile. For measurements that fall between tape sizes, it is still required that two readings using each tape are to be averaged to comprise one reading d441.

Summary of Test Method 2. Work Item s – proposed revisions of this standard. This standard is subject to revision at any 4d417 by the responsible technical committee and must be reviewed every? While both the depth micrometer and replica tape methods conform to ASTM D, the measurement acquisition principles are quite different.

Updates to ASTM D4417

Your comments will receive careful consideration at d44417 meeting of the responsible technical committee,1which you may attend Copyright? There are currently four primary standards for measurement of surface profile in steel surfaces.

This can be discussed and agreed upon at the pre-construction conference. During abrasive blast cleaning, the mass of the abrasive and the velocity of the abrasive movement created by compressed air generates kinetic energy the abrasive can reach speeds of over miles per hour as it exits the blast nozzle.