74LS164N DATASHEET PDF

March 22, 2021 0 By admin

74LSN from Fairchild Semiconductor. Find the PDF Datasheet, Specifications and Distributor Information. 74LSN Datasheet, 74LSN PDF, 74LSN Data sheet, 74LSN manual, 74LSN pdf, 74LSN, datenblatt, Electronics 74LSN, alldatasheet. These 8-bit shift registers feature gated serial inputs and an asynchronous clear. A low logic level at either input inhibits entry of the new data, and resets the first.

Author: Vojora Mezigis
Country: Angola
Language: English (Spanish)
Genre: Music
Published (Last): 3 April 2004
Pages: 412
PDF File Size: 19.60 Mb
ePub File Size: 2.43 Mb
ISBN: 586-9-26954-876-6
Downloads: 59402
Price: Free* [*Free Regsitration Required]
Uploader: Vudokinos

For example if the pin — outs 1 and 2 are permanently connected to the positive supply and the reset pin is joined to the last output of the IC pin 13then, as discussed earlier, once all the outputs become high the last pin 13 instantly resets the whole circuit, shutting the whole array of outputs, and the cycle repeats.

That’s pretty far fetched, given the frequencies involved. Sign up using Facebook. Similarly the IC requires only an external clock signal to make its outputs swing into action and produce interesting logic sequences. Hasn’t ever happened to me.

I took some photos of the scope, the first is the clock from the GPIO without nothing and the second is the clock connected to the datashfet. Perhaps this has something to do with your problem. Thus exceeding operating conditions, all bets are off.

Just disconnect the LEDs and use the scope to check outputs. You have an unexplained 1V offset. Finding out where that offset comes from should be the absolute first priority here.

74LSN datasheet, 74LSN datasheets, manuals for 74LSN electornic semiconductor part

Better yet, JamesMagnus, you have a scope. You should test with the FETs in place.

You are probably getting multiple pulses instead of just one. Output mode is push-pull with at least 2mA sink capability. The register was clocking multiple times because the clock signal wasn’t enough clean.

  LOONEYSPOONS COOKBOOK PDF

Email Required, but never shown. 74lw164n I added a schmitt trigger between the raspberry pi and the register clock input, and now it shifts exactly the number I want. Or, the pulse has a ragged edge s and the is actually clocking several times.

FiddyOhm Reading the datasheet here, I can’t find an issue with the logic levels. Sign up or log in Sign up using Google. Through a few of my previous articles I have tried to cover the working principles of a couple of versatile ICs like the and Referring to the figure on the left we see that externally it looks just like an ordinary pin dual in-line chip.

The extreme top left pin from the printed side is the first pin in the order, and the pin just opposite to it on the other row is the last or the 14 th pin.

The extreme top left pin from the printed side is the first pin in the order, and the pin just opposite to it on the other row is the last or the 14 th pin.

Then I send a clock pulse from the Raspberry Pi go high for ms then go low. This opposite sequencing also takes place in accordance to the rising pulse of the input clocks.

Similarly the IC requires only an external clock signal to make its outputs swing into action and produce interesting logic sequences. Looks pretty clean but you need to zoom way in to know for sure. This opposite sequencing daatsheet takes place in accordance to the rising pulse of the input clocks.

Результаты поиска для 74LS164N

Now suppose if through a simple wiring pins 1 and 2 are configured in such a way that when the last pin 13 of the IC goes high while sequencing serially, it grounds the serial input 1 and 2.

  DIVINE ENCOUNTERS SITCHIN PDF

The thresholds are 0. What am I doing wrong? Negative seems to indicate 47ls164n current, and positive sink current. Introduction Through a few of my previous articles I have tried to cover the working principles of a couple of versatile ICs like the and The serial inputs pin 1 and 2 of the IC has a special purpose of resetting the above procedure in an interesting pattern.

Referring to the figure on the left we see that externally it looks just like an ordinary pin dual in-line chip. When I power-on the circuit, all the LEDs are off. For example if the pin — outs 1 and 2 are permanently connected to 7l4s164n positive supply and the reset pin is joined to the last output of the IC pin 13then, as discussed earlier, once all the outputs become high the last pin 13 instantly resets the whole circuit, shutting the whole array of outputs, and the cycle repeats.

74LS164 – 8-Bit Shift Register Ser In/Para Out

By using our site, you acknowledge datasgeet you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

In real I will put mosfets to control a big led board.